The 3000 Mile Oil Drain Fails To Address The Real Issue

The 3000 Miles Oil Change Interval Doesn’t Address Oil Quality

When people say to me they change their oil at 3000 so not to take any chances that dirt could be causing damage or the oil could be getting “bad”, I say to them, why not change every 50 miles then?? I’m sure the oil is still good but as you said, why take a chance?

Let’s look at the top reasons for engine failure which relate to the oil.

#1 is lack of lubrication. Nothing to do with dirt but a poor quality non-synthetic even low quality synthetic made from Group III base stocks (There are over 80 different quality levels for a Group III oil thus lower prices – this does not fit the scientific definition of synthetic) can and will leave deposits OR lose viscosity early on both causing lack of lubrication.
#2 – Overheating – Often the damage done after a engine overheats is caused by the heat being too intense for the oil to hold its properties. An AMSOIL product would have prevented this especially in air cooled (V-Twin bikes or marine) and in the new trend of turbocharged engines. The coming LSPI issue will demand the oil be at least a 100% synthetic quality. It’s designed for temperatures beyond these issues.
So changing oil every day will not prevent the above. Any overheating event or the list of reasons which cause a lack of lubrication cannot be addressed by the 3000 mile oil change. Only by the quality of the oil. AMSOIL also adds performance and for the difference in price per quart is less than the cost of a cup of today’s coffee so the solution for protecting your investment is here!! And has been for 45 years.

Quality Oil Filtration is a Must but still only part of the issue

I couldn’t find the study as I was writing this but Federal Mogul published research that “dirt” in oil was actually a minor part of failure while things relating to lubricant quality were. Acids or loss of TBN was a much more severe issue. Corrosion and storage was a far greater contributor to reduction in engine efficiency and ultimately failure.

Mild quality oil filters solve the dirt issue for up to 10,000 miles but you still need an oil which can fight contaminants caused by fuel or advanced wear over the years (such as starting with a used vehicle which you don’t know the history of). AMSOIL addresses the contaminants with their advanced additive packages and are willing to cover that with a guarantee.

How do you know?

Note while that AMSOIL does back their oil for longer intervals, this is clearly stated for engines which are in normal operating condition and have not been modified. For modified engines, neglected ones or those with a good number of miles over 100,000 they do list severe service categories or one can always get our KIT-02 oil analysis kit and go from there.

Just use better oil and find out what you are missing!

AMSOIL use will tilt the scales of a nations fleet replacement statistics. Imagine that. Just from changing brands of oil.

The 3000 mile oil change interval excuse is much like arguing one brand of cigarettes is more healthy than another.
Use AMSOIL and unlock the full potential of your drive train!! Find out what others already know – AMSOIL is all about performance!
Ches Cain – AMSOIL Direct Jobber

Engine Deposits can be Prevented using Superior AMSOIL Lubricants

Help Preserve Your Engine’s Horsepower

Although you may equate engine wear and deposits with sudden, catastrophic engine failure, they are more likely to erode engine power and efficiency over time. Here’s how it works and what you can do about it.

Several factors cause an engine to slowly lose power, but one of the primary reasons includes compression loss due to wear and deposits.

Engine compression = power

For your engine to produce maximum power, the combustion chamber must seal completely during the compression and combustion strokes. Wear and deposits can prevent the valves or piston rings from sealing, allowing pressurized gases to escape the combustion chamber and take potential engine power with them.

To illustrate, imagine using a hydraulic floor jack. Pumping the handle will raise the vehicle as long as the release valve is tightly seated and doesn’t leak. A poorly sealed release valve, however, allows pressure to escape, causing the vehicle to sink to the ground no matter how much you pump the jack handle.

The same principle applies inside your engine. If some of the pressure created during the compression and combustion strokes is lost due to valves and piston rings that don’t seal completely, the engine will create less power.

Wear & deposits reduce compression

Over time, deposits or valve wear can prevent the valves from closing completely, interfering with a good seal. Wear can also interfere with proper valve operation, disrupting optimum fuel/air flow.

Worn or stuck piston rings produce the same effect. The rings are designed to move freely in their grooves and press tightly against the cylinder wall, forming a seal that prevents fuel/air from escaping. Ring wear can interfere with formation of a tight seal, while deposit buildup can cause the rings to stick in their grooves, also preventing a good seal. As a result, some fuel/air escapes the combustion chamber during compression, reducing power. On the combustion stroke, pressurized gases can blow by the rings and travel down the cylinder wall and into the oil sump, taking potential power with them. This is what’s meant when someone says an engine has lost compression.

AMSOIL Signature Series helps prevent the problem

A lot is working against you including the quality of the gasoline available here in Sioux Falls. Everything you can do to prevent deposits goes a long way saving you money in the long term no t to mention engine life. AMSOIL Signature Series Synthetic Motor Oil provides 75 percent more engine protection against horsepower loss and wear than required by a leading industry standard*, extending the life of vital components like pistons and cams. In addition, it prevents piston deposits 93 percent better than required to meet the latest API standard.* Its outstanding performance helps prevent deposits and wear that rob engines of horsepower, helping preserve that like-new feeling you crave when driving. The secrete is in the low volatility of the oil. That can only happen when quality is the main driver of the firm.

*Based on independent testing of AMSOIL Signature Series 5W-30, in ASTM D7320 as required by API SN specification

Ches Cain – AMSOIL Direct Jobber

Your Sioux Falls Power Gain by Oil company. Most AMSOIL customers discovered AMSOIL via word of mouth due to performance only!! Not because our products save fuel or last 3X longer. It’s the real benefit of performance you can feel!! So compare that to other brands and more research will unveil the BIG lie they “don’t” offer to the consumer as advertised. AMSOIL is a family owned and operated business. No greedy stockholders to effect the choosing of additive packages.

Tag: engine